Skip to content

Find the cause, then the fix. Free in-home estimates: (562) 837-0159

(562) 837-0159

ServicesSliding Door Replacement

Sliding Door Replacement in Cerritos

A sliding door that drags, leaks or won't lock usually has one root cause, and it isn't always the door. We find that cause first. Then we replace the unit with a door sized, sealed and leveled to your opening, so it rolls easily and closes tight.

Installer in gray work gloves lifting a white-framed sliding glass door panel beside an open door frame on a stucco house with a covered patio and backyard fence

When replacement is the right fix

Many sliding doors we see went in with the house: single-pane aluminum frames on steel rollers riding a thin aluminum track. After decades, the rollers flatten, the track wears a groove, and the frame twists enough that the latch no longer meets its keeper. New parts rarely hold at that stage, because the frame itself is out of shape.

Sometimes the cause sits outside the door. A sagging header, a settled slab or a sill that was never pitched to drain will ruin a new door just as it ruined the old one. We check the opening with a level and a tape before we quote, so you know exactly which problem you are paying to solve.

Window Replacement Cerritos is CSLB C-17 licensed and has been in business for 12 years. Our installers bring 30 years of window installation experience, and that same care goes into fitting large glass doors.

What a sliding door replacement includes

Measuring the rough opening
We measure width at the top, middle and bottom, and height at both jambs. We check the diagonals for square and the sill for level. Those numbers decide the door size and whether the opening needs shimming or correction first.
Removing the old door and frame
Panels come out first, then the frame. In a retrofit we keep the existing frame where it is sound. In a full-frame job we cut back the stucco or trim to reach the nail fin and take the whole unit out.
A new dual-pane tempered unit
Glass in doors must be tempered safety glass, and every unit we install is. You choose vinyl or aluminum frames and a glass package, including Low-E coatings that cut summer heat gain through a wide pane.
Sill pan, flashing and sealant
Most leaks at a slider start at the sill, not the glass. We set the new frame on a sill pan, lap the flashing so water sheds outward, and keep the weep holes clear so the track drains.
Adjustment, hardware and cleanup
We set the roller height so the panel tracks evenly, align the latch with the keeper, and fit the screen. The old door is hauled away and the work area is vacuumed before we leave.

Signs your sliding door needs replacing

  • It drags or jumps the track

    Worn rollers and a grooved track make the panel grind or lift out of place. If adjusting the rollers no longer helps, the track or frame has worn past the point of holding a setting.

  • Water at the sill

    Puddles inside after rain or sprinklers mean the sill is not draining. Clogged weep holes are one cause. A sill with no pan or a back-pitched slab is another, and replacement lets us correct it.

  • Fog between the panes

    Haze that no cloth can reach from either side points to a failed edge seal on the insulated glass unit. Damp air now moves in and out of the space between the panes, and the insulating gas sealed in at the factory escapes through that same gap, so the door no longer holds back heat as designed.

  • The latch won't catch

    When the frame racks out of square, the latch misses the keeper. That leaves the door hard to lock, which is a security problem as much as a comfort one.

  • Hot glass and drafts

    Single-pane glass passes heat straight through on summer afternoons, and worn weatherstripping lets air in at the interlock. A modern Low-E unit addresses both.

How the job runs

  1. 1

    Your call and the estimate

    Call us and we will set a time for a free in-home estimate. We look at the door, the track and the opening, then explain what we found.

  2. 2

    Diagnosis and a written quote

    You get a quote that names the door, the frame material, the glass package and the installation method. If the opening needs work, it is listed as its own line, not added later.

  3. 3

    Installation day

    We lay drop cloths, remove the old unit, prepare and flash the opening, and set the new frame level and plumb. If your project needs a permit, we handle it.

  4. 4

    Final adjustment and walkthrough

    We roll the panel, test the lock, and run water over the sill to confirm it drains. Then we show you how the door and screen operate.

Estimator in a navy polo measures an old window on a stucco house's side wall with a tape measure while the homeowner holds a clipboard

What moves the price of a new sliding door

Two things set most of the quote: the unit you pick and what we find in the wall around it. We go through every line with you before you commit, so the number you approve is the number you pay. Our in-home estimates are free, with no sales pressure or obligation.

Size and panel count
A standard two-panel door costs less than a wide three- or four-panel unit. Larger glass also needs more crew to handle safely.
Frame material and glass
Vinyl and aluminum frames are priced differently, and Low-E coatings, laminated glass or tinted options add to the glass cost.
Retrofit or full-frame
A retrofit into a sound frame takes less labor. A full-frame removal means cutting stucco or trim and patching it afterward.
Condition of the opening
A sagging header, rot in the framing or an out-of-level slab has to be corrected before the new door goes in. We find these at the estimate so they are priced up front.

Sliding door replacement questions

Something not covered here? (562) 837-0159

How long does it take to replace a sliding door?

A standard retrofit is usually finished in one day. A full-frame replacement with stucco work can take longer. We tell you the expected schedule at the estimate, so you can plan around an open wall.

Can you put a new door into my existing frame?

Often, yes. If the old frame is square, solid and draining properly, a retrofit saves labor and avoids stucco repair. If the frame is twisted or the sill leaks, a full-frame replacement is the better fix, and we will explain why.

Should I choose vinyl or aluminum?

Vinyl insulates better and resists condensation on the frame. Aluminum allows thinner frames and more glass for the same opening. We bring samples to the estimate so you can compare how each one looks and operates.

Can I replace a two-panel slider with something wider?

Widening an opening means resizing the header, which changes the structure and the cost. If you want the wall to open fully, ask us about our multi-folding doors. We can look at both options at the same visit.

Is the estimate really free?

Yes. We offer free in-home estimates with no sales pressure or obligation. You get a written quote and time to decide.

Two-story stucco house with new black-framed windows still showing stickers, a stepladder, trash can and drop cloths on the front walk under the porch

Find out what your sliding door actually needs

We'll check the track, the frame and the sill, then tell you plainly whether replacement is the answer and what it involves. Homeowners in Cerritos, Artesia, Norwalk and nearby towns can book a visit with one call.