ServicesWindow Retrofitting
Window Retrofitting in Cerritos
Retrofitting puts new, efficient windows into your existing openings without cutting back stucco or tearing out drywall. Before we recommend it, we check each frame for square, water damage and movement, so the new window seals tight and stays that way.

What a Retrofit Is and When It Fits
In a retrofit, we take out the old sashes and fixed glass, leave the original frame in the wall, and install a new window inside it. In stucco walls we usually use a flush-fin (Z-bar) frame that laps over the old aluminum frame and gets sealed against the stucco face. The exterior finish, the interior drywall and the trim stay where they are.
It works well for the original aluminum sliders found in many Cerritos homes built in the 1960s and 70s, as long as the old frame is solid. If the frame is bent, rotted at the sill or has let water into the wall, a retrofit only covers the problem. In that case we tell you so and explain full-frame window replacement instead.
We are CSLB C-17 licensed, and our crew brings 30 years of window installation experience to each opening we measure.

What Your Retrofit Includes
- 01
Frame inspection before any order
We check each existing frame for square by measuring the diagonals, look for corrosion at the sill track, and probe for soft wood or water staining around the opening. This tells us whether a retrofit will seal properly or whether that opening needs a different approach.
- 02
Three-point measuring
Width and height are measured at the top, middle and bottom, and the window is sized to the smallest reading. Old openings are rarely true, and ordering from one measurement is how gaps happen.
- 03
Removal of old sashes and glass
We pull the sliding panels and fixed lites, clean out the old track and remove loose debris and failed caulk so the new frame sits on a clean, flat surface.
- 04
Flush-fin or insert installation
Stucco walls usually get a flush-fin frame. Wood-trimmed openings often take a block-frame insert. Either way the window is shimmed level and plumb, fastened, and checked to slide and lock smoothly.
- 05
Weatherproof sealing
We seal the perimeter with an exterior-grade sealant and keep the weep holes at the bottom of the frame clear so water that gets into the track can drain out instead of into the wall.
- 06
Cleanup and walkthrough
Old glass and frames leave with us. Before we go, we open and lock each window with you and point out how the weeps and screens work.
Questions about Window Retrofitting?
Call(562) 837-0159Signs Your Windows Are Ready for a Retrofit
Sliders that drag or jump the track
Worn rollers and pitted aluminum tracks make old sashes hard to move. If the frame itself is still straight, replacing the window inside it fixes the operation for good.
Fog between the panes
A cloudy look inside dual-pane glass means the seal has failed and the insulating gas is gone. The unit no longer insulates the way it was built to.
Single-pane glass and hot rooms
Original single-pane aluminum windows pass heat straight through. A retrofit with Low-E dual-pane glass cuts that gain without disturbing the wall.
Condensation on the frame
Aluminum frames with no thermal break sweat on cool mornings, and that moisture can stain sills and feed mildew. New vinyl frames stay much closer to room temperature.
Drafts and street noise
Gaps around old sashes let in air and sound. A new frame with fresh weatherstripping and dual glazing closes those paths.
How a Retrofit Job Runs
- 1
Free in-home estimate
We look at every window, check the frames and talk through glass and style options. You get a written quote that lists each opening, with no sales pressure or obligation.
- 2
Order and permit
Windows are made to the measurements we took. Where the city requires a permit, we pull it, and we choose glass that meets California's Title 24 energy rules.
- 3
Installation day
We work one opening at a time, so a room is never left open for long. Most homes are finished in a single day, depending on the number of windows and how many are on a second floor.
- 4
Final check
Each window is tested for smooth operation, lock engagement and a continuous seal. We clean the glass, haul away the old units and leave the rooms the way we found them.
What Moves the Price of a Retrofit
Retrofitting usually costs less than full-frame work because the walls and finishes stay in place. Your quote depends mostly on how many windows you have, how big they are, and what we find when we check the frames. We price each opening separately so you can see where the money goes.
- Window count and size
- Larger openings need heavier frames and more glass. Ordering several windows at once usually lowers the per-window cost of labor and setup.
- Glass package
- Low-E coatings, tempered glass near doors and tubs, and obscure glass in bathrooms each change the price. Code requires tempered glass in some locations, and we note those on the quote.
- Window style
- Sliders and single-hungs are the most straightforward. Casements, picture windows with grids and specialty shapes cost more to build.
- Frame condition
- If an opening shows rot or water damage, a retrofit is not the right fit there. We price that opening for full-frame work and show you why.
- Access
- Second-story windows and openings behind landscaping or fixed structures take more time and equipment to reach safely.
Window Retrofitting Questions
Will a retrofit damage my stucco?
No cutting is needed in a standard retrofit. The flush-fin frame laps over the existing frame and seals against the stucco face. Your exterior finish and paint stay as they are, apart from a clean caulk line around the window.
Do I lose any glass area?
Usually a little. The new frame sits inside the old one, so the visible glass shrinks by roughly the thickness of the new frame. For bedroom windows we confirm the clear opening still meets the code minimum for a bedroom escape window before we recommend a retrofit.
Is a retrofit as energy efficient as full-frame replacement?
The glass and the new frame perform the same either way. The difference is the seal around the opening. That is why we confirm the old frame is sound first, because a good retrofit on a solid frame seals just as tightly. Our Energy Efficient Windows page covers glass options in more detail.
How do you decide between retrofit and full-frame?
It comes down to the existing frame. If it is square, solid and dry, a retrofit is the faster, cleaner choice. If it is warped, corroded through or there is water damage in the wall, we recommend full-frame window replacement for that opening and show you what we found.
How long have you been doing this work?
We have been in business for 12 years, and our installers have 30 years of window installation experience. That history is why we measure every opening several times and inspect the frames before ordering anything.

Find Out If Your Frames Are Retrofit-Ready
We will check each window, tell you which openings suit a retrofit and which do not, and give you an itemized quote. We serve Cerritos and nearby towns including Artesia, Norwalk and Lakewood.